Planning an eQSL card, hunting for signals

I find that in addition to not having a Nobel or a Pulitzer prize, also graphics is not my virtue but then again, we all do our best – don’t we. So here’s a world premier for my eQSL card.

Picture shows something I anticipate to be doing quite a bit in the future, going mobile (or /M in ham lingo) as the formal QTH does not offer much in terms of signal reception. There is a huge difference being mobile, much less RFI when at suitable locations and of course a dramatically better signal quality.

Thinking about the Ciro Mazzoni smaller loop and some sort of a roof rack.

Car has a CB radio currently, next will be a dual-bander (2m/70cm) and if the continued testing of the relatively small size magnetic loop turns out even more promising, also HF.

It may very well be that other than for easier bands like 20 meters, HF will primarily have to be worked on mobile. Thus there will be a distinction between ham activities at the QTH and on the road.

In the frantic search for signals I connected a capacitor with the balcony fence last night.

That huge steel structure basically did work as an antenna, but I would say that if balcony steel fences made such great antennas more people would use them. Did not much bother to test TX nor SWR, but had to cross off the balcony fence from the “todo-list”. So there, I’ve done it.

During the weekend I also spent quite a bit of time just listening to the ongoing contests. Those are good sources for reception, and improve in particular the hearing and recognition of call signs. It is great fun searching the ‘Net for identified call signs, not just because it gives an indication of how far those signals originate from – but also quite a few hams have nice and personal pages at QRZ and similar sites.

Last night I listened to S57DX, Slavko from Slovenia. Reception was strong and clear on 20 meters, and I also appreciate his punctual speech style.

– 73 de OH2BNF

 

OH2BNF goes mobile

35963551_802982353231712_1106100339536297984_n

As a typical apartment dweller antenna restrictions and abundant RFI apply, hence I had to come up with something that would enable me to get good signal quality across most common ham radio bands.

I started off by constructing an adapter cable that would allow me to ad hoc power the Icom 7200 from the car battery, without making a permanent installation to the vehicle.

35882400_801071270089487_6793060286992482304_n

This set with the jaws allows for a quick connect/disconnect under the hood

36029573_801286883401259_5925337096309964800_n

and with sufficient length for both the power and RG58 cabling, transceiver can be operated from inside the vehicle while loop antenna is located on the roof

35971428_802985409898073_5762325911852548096_n

aforementioned antenna being a converted aluminum hula – hula loop with roughly a 1 m. diameter, attached to a MFJ-936B as following pictures indicate

23659510_705953119601303_4759343350261260821_n

25182299_714663275396954_3285939193445518288_o

this setup turned out to be quite good, extending beyond its “by design” frequencies as I was able to enjoy good RX even on the 80 meter band, which is certainly not in the comfort zone of a 1-meter loop.

RESULTS

  • finally had sufficient signals to focus on transceiver itself
  • 80 meters was a major surprise – had not anticipated it with this loop spec
  • e.g. on 20 meters I had crisp clear reception from range of at least 2600 km
  • learned to tune both the antenna and the transceiver, so that…

…could pretty much duplicate the reception at home with antenna on the balcony!

Outcome of this is that when new to the ham radio or for example specific equipment, it is important to see the effort to have an abundance of signals to work with – different bands, reception types and conditions prevailing

  • Increases familiarity with your overall station setup
  • Teaches a bunch about the transceiver in particular
  • Supports hunting down weaker signals later on at QTH

 

73, de OH2BNF